Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
So I want to run the nRF52811 chip so I removed the nRF52832 chip from its development kit and soldered the nRF52811 chip but I cannot seem to program it. What are the required...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
Hi.
I am developing application with mpu6050 gyro on nRF52832, swd S132 V6.1.1., sdk 15.2. My code is based on ble_app_uart. In main, I add my custom function that calculates...
Hello!
I was going to start to program my Thingy 91 but since I don't have a J Link Programmer cable or a nRF9160 DK. I was planning to use mcuboot like suggest this documentation...
Hi,
I am working with MPU6050 gyro. I run the examples from GitHub for nRF52. Everything works fine, bit I have an issue with gyro output data. In register map documentation...
I'm new to Nordic, I just got an nRF 52 DK. Refreshingly simple to get working with Segger Embedded Studio on Mac. I'm particularly interested in the BLE multiperipheral application...
Hi,
I'm trying to build the asset tracker off the master branch in windows 7. I did do west update. Using gcc version 7.3.1 20180622
It fails like below. Any ideas?
...
Hello,
I have the following issue. I am developing an application very similar to the "ble app hids keyboard" example. SDK 15.0, S132 V6.0.0, nrf52832.
I would like to...
Hi!
Previous tickets 234795 and 231307 asked about the status of field updates of the nRF9160 modem firmware. Some solution is coming, but unclear when.
Are there any...
We are developing with the nRF52840, in this instance present in a Laird BL654 module carried by their DVK-BL654 dev board.
After trying three separate examples that attempt...
Hi all,
I need to be able to reprogram an nRF52832 on a daughterboard from a mainboard with a Cortex M7. I have been able to eraseall and reprogram the nRF52, but it seems...
I have searched this site and not found an answer, although this seems to be a similar question: https://devzone.nordicsemi.com/f/nordic-q-a/41853/usb-driver-install-fail...
Hi,
I am stuck in sending and receiving serial data over Rx and Tx in nrf51 DK. I used arduino to prototype a fingerprint access control system. Now I am shifting to nrf51...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
