I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Helo, Im trying to sending data from sensor between two nrf52832, SDK 15.0.0 SoftDevice S140 on both. Im using uart central and peripheral examples on transmiter and receiver...
Hello,
Like in the description, I dont get this to work. Im trying to get The nRF24L01+ connected to a PIC16LF18345. I did Some Pictures of the SPI logic and Here is a Part...
I have the nRF52840 PDK and tried to download the firmware as per step 7 to paste it to the JLINK folder to make LED1 blink so i can test NFC but cannot get led 1 to blin...
I was wondering if adding a capacitor in parallel with the coin cell battery would help with the battery life by smoothing out the peaks. The scenario shown in the chart is...
Hello All,
I have successfully built the secure_bootloader app. I have the bootloader working with the button. I can upload application files using DFU. I tried the buttonless...
Hello
I'm currently running ble_app_uart__saadc_timer_driven__scan_mode and would like to modify it for faster sampling rate. However, NRF_ERROR_RESOURCE presents an obstacle...
Very new still learning.
I am using Keil and trying to setup the tools>customize tools menu.
Following the tutorial I am able to create the eraseall macro. No problem...
Hello~!
I am working on modifucation code of ble_app_uart example.
nRF51822
(SDK12.3.0_d7731ad)
Softdevice 130 (v2.0)
I know the original UUIDs are provided from...
Hi, I am working with the example Blinky_freertos present on the SDK_13.0.0_04a0bfd.
I have built the example w/o issues in compilation but I have the following problems...
Hi i get this error when compiling. (version 0.9.7)
I'm using arduino DUE and BLE Shield (redbearlab).
I get the error: EEPROM.h: No such file or directory in bootloader_setup...
I tried building ' pca10040 ' configuration of " nrf52-mpu-easydma-using-gpiote-and-registers " example from " https://github.com/Martinsbl/nrf5-mpu-examples ". The following...
Hi
I am working on nRF51-DK with Mbed IDE & used PWM example code from link : https://os.mbed.com/handbook/PwmOut
When enabled PwmOut, PWM signal is observed on the oscilloscope...
I would like advice on whether the following is a valid ble transaction.
We have a product with the nrf52 in it running sdk 12 and softdevice 3.0. This is setup as a a peripheral...