Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hey,
I’m using Arduino IDE to program my nRF52832. I want to connect two nRF52832’s using BLE for master-slave communication. Eventually I want the master to control multiple...
Hi,
I am using nRF52840 DK, and I am creating my program starting from the basic UART example. I am not using threads, just plain sequential execution. I have a chain...
Hi,
I found out, that in the light switch example (SDK for Mesh v.1.0.1) after adding second element with Simple OnOff model in the light_switch_server, it is not possible...
Hi! Im using a nRF51-dongle and the SDK v12.1. There are no exampels for Segger Embedded Studio but in Segger Embedded Studio im trying to use the "Import IAR EWARM/KEIL MDK...
Hi everyone!
Im using Segger embedded studio and its works well to import the keil project to SES. I dont get any errors when building or debugging but i cant se it in the...
I read that in large networks that configuring the relay nodes helps achieve low-latency communication. With the nRF Mesh, is it possible to automatically switch off the relay...
Hello,
I wanna use FDS module and started with FDS example given in SDK 11.
I have used the exactly same functions for initialization but it seems like FDS module is not...
The S120 Central after scanning, connecting, and issues a sd_ble_gap_encrypt() to secure the link. If the peripheral's bond (LTK) is corrupted or incorrect, the sniffer shows...
This: http://www2.keil.com/mdk5/editions/lite/
I guess the principal limitation is the 32K code size, but the full list is here: http://www.keil.com/demo/limits.asp
...
I have Stlink v2 programmer and I would like to use it to flash hex file into my nrf52832 I read a lot of threads about using tools like openocd but none was helpful, I think...
I'm attempting to build the ble_app_hids_keyboard example from sdk 14 using gcc and the compiler is throwing the error "No such file or directory", but the file is there and...
I have problem on SoftDevice V6.0.0(nrf52832) scan_start/stop. modified ble_app_blinky_c(ble_central) 1. app_timer add (20ms cyclic) 2. app_timer handler, run sd_ble_gap_scan_start...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
Hi,
I've defined:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 120 (in sdk_config.h)
I get "Insufficient RAM allocated for the SoftDevice" in nrf_sdh_ble_enable
nrf_sdh_ble_enable...
