Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
After experiencing UART problems without handshaking I opted to enable hardware handshaking.
Where RTS & CTS are pins 5 & 7 respectively.
I was experiencing overrun (insufficient...
The nRF6905 nRFready Basic Remote is a complete hardware and software reference design for basic 2.4GHz RF remote controls.
What nRF24LE1 devices are included in the hardware...
hi sit and test bluetooth mesh and i do not quite understand how the client knows that the server is off or on and there is a way to find out if a server is on or off
Hello,
I would like to use nRF52840 in order to make some BLE5.0 mesh products. When I open the nrF5 for mesh, I can see only examples for nRF52832.
Do you know if these...
hello, i am trying to implement external RTC in my application. i am using the SDK 14.2.0 and softdevice s132 .n also for external RTC using the M41T62 with nrf52832DK. so...
Maybe there's a secret I'm missing but this looks like a development / debug flag that got left in.
I'm porting an app from SDK11 to SDK15, when I call app_button_init(...
Hello
There seems to be no makefile in this example to use with armgcc compiler(why?) so Im trying to port it using the makefile from the ble_app_att_mtu_throughput example...
How to write driver for ADC by accessing direct registers of nRF52840 ?
I don't wanna use SDK APIs.
I wanna read LDR value connected to A0 (PO.3) pin in continous mode...
Dear all,
I'm trying to change the advertised device name during advertising depending on some variables.
I'm observing with nRF Connect and Lightblue, both running on...
Hi,
I have followed the steps for the 2 demos for nRF52840 DK, the Heart Rate and the Proximity demo. In both cases, when disconnected from the android device, the evaluation...
Heey everyone,
I'm currently working on a wireless application and we would like to have a range of atleast 300 meter. Yesterday I was testing the range between 2 SDK...
I work with Kenkou GmbH in Berlin. We are looking for Firmware Developers and Engineers with Mid - Senior experience to support our project. We are hoping to extend the visibility...
Hi All, Nordic,
In my application, I don't always need BLE connectivity, so I was hoping to disable the S132 softdevice when not needed. However when I do this FreeRTOS...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
