Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello everyone,
I'm trying to implement the bootloader from SDK v14.2 on the nRF52840, SD v5.0.0 s132 (using our board and app).
For my testing, I erase the whole flash...
Hi Forum,
i've started the development of an custom service on a nrf51822 with s110.
The Service contains 4 Characteristics where notifications are enabled.
At the...
I have a custom dongle that connects to the PC through a USB-UART chip. It is based on the nRF51822. I have another board based on the nRF52832. This board needs to be able...
Hi,
I am building a device to act as an iBeacon, with other services layered on top. This is based on a Raspberry Pi with a Class 1 USB Bluetooth dongle.
I need to be...
Hi everyone, I'm working on the nrf51822 QFAAH I tried to flash the ble_app_uart example and it didn't work. So I debug it and it stops here
As you can see in the picture...
I am working on app_uart and buttonless_dfu. Although i am getting certain errors which i am unable to counter.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
I have 32x64 RGB LED Matrix, and I want to use nrf52 to control it. I got the driver working and I can display everything. It is a time interrupt driven driver, just redraws...
So I just got my nRF52_DK, got everything installed and compiled an uploaded the blinky example. Fine. I had my custom PCB ready, and got the 52832 soldered in straight away...
Hi, I am a newbie to embedded development. I am well versed with java script. I am under the impression nordic allows you to communicate with java script to the development...
Hi, we're using \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hids_keyboard to test Pairing/Bonding/whitelist.
After connection, when the central try to read...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
