Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
When I use nrfutil to generate a zip package, there would be three document in the package. Is there anyone know what does .dat and .json document use for? Could I...
Hi there,
I am begineer for nrf51822 and I want to interface MPU6050 WITH nrf51822 so can somebody provide me the tutorial with full detail.i want to read just raw values...
Have been following the nordic tutorial to update characteristic value using hvx_params. Currently the structure for hvx_params is as follows:
/**@brief GATT HVx parameters...
Hello every!
I am working with ATT_MTU_Thoughtput example (S132). My purpose is send data from "sever" to "client" and wait until "client" response to confirm . I was send...
I’m debugging the ble_app_blinky demo on a nRF52840-Preview-DK board (BOARD_PCA10056, S140). The device name in the debug configuration is nrf52832_xxaa.
Each time a breakpoint...
Hi all,
i use a nrf52 and in product specification i find the table about the low power mode and their consumption . Capter 17.1.
ION_RAMOFF_EVENT System ON, No RAM...
Hi all,
I have been playing with my PCA10040 and I came across the problem. I thought that it was a softdevice problem, so I went to bootloader mode (by connecting with...
Hi,
would it be possible to have multiple GAP Addresses for one nRF device? I was able to have this with the S130/S132 using verison 2.0.1 by using gap_address_set and...
Hi,
I have nRF52840 dev board which was detected and LEDs were coming on.
I tried programming the prebuilt throughput hex file in nRFgo Studio.
C:\Projects\NORDIC\nRF5_SDK_14...
Hello dear sir/madam, i have just started with BLE using nRF52832 DK .but i am not able to understand the examples.and don't know how to make any change.what is the basic...
My nRF5x DK kit has suddenly stopped working and I experience one or more of the following symptoms:
My kit doesn't show up in my computer.
LED 5 on my kit doesn...
Hi,
I have a ble scanner working well and i am trying to trigger start a compare timer within a timeslot.
starting the timer in the timeslot with the below code makes...
How does scanstart serial command work in the Mesh SDK?
According to the documentation, it appears that the command lists out unprovisioned beacons. I get a success response...
Hello,
1.We have to implement multi pal peripherals and one central.I have to send data(some sensor data) between it periodically....using NUS sample it is possible??
...
