Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi everyone,
I'm using the nrf52832 Dev Kit PCA10040
SDK version: 15.3.0
OS: Fedora
I try to use DFU following this tutorial but I don't get the DFUTarg on the...
Hi pals!
I'm trying to establish throughput test with two nRF52840 DK and it works perfectly well except the coded PHY option. When I configure the phy option to coded,...
HI,
I am playing around with the "usbd_ble_uart_freertos" example of SDK version 15.3.
When I create another Task and try to write log entries (NRF_LOG_INFO("Test")) i...
Hi,
As well know, there have 100 channels in ESB function in nRF52832, but 2.4GHz also share with Wifi and Bluetooth.
So there have many noise if I choice wrong channel...
Hi!
I am experimenting with the ble_app_hrs_freertos example.
I would like to start two additional tasks. All works until a ble conection is made. after that my created...
Hello
I am using FDS to store some MAc addresses in my project. After successful I try fds_init() which returns error 11.
I can't figure out what is causing this error...
Hello, I have been trying to get the nrf9160DK PCA10090 version 0.8.2 to connect to your nrf cloud. I initially tried with the provided ibasis sim. I was able to get it registered...
Hi,Master:
1.The timing of the underlying nrfx_qspi_write(...) function is:a. Send 05 to check if the wip bit is 0. (Here, if wip is not 0, will it always detect until wip...
Hello,
I am going to be heading to a certification house to run tests to pass for the CE mark for our product that we used the nrf51822 on. The BLE portion of our product...
Hi everyone,
I'm trying to establish throughput test using mtu_throughput example(central-peripheral) and 2 nrf52840's but I keep getting error when set phy to coded. Here...
Hello All,
I want to know if I can run all this protocol at once? if yes can I find an example or can you suggest me a guide? I know there are examples to use BLE and ANT...
Hello, I'm attempting to establish a data connection on the VZW network after uploading a VZW IMEI to the ODI portal. It appears there is no module available under the Nordic...
We are incorporating a filesystem for NAND flash driven by the NRF52, but we are running into performance issues using littlefs and want to do deeper troubleshooting. From...
Hi Everyone!
I really need some help. So I'm new to Nordic semiconductors and Segger Embedded Studio IDE. I purchased myself an nRF52832 breakout from sparksfun and nRF52832...
Hi,
I am trying to test the Amazon FreeRTOS BLE demo ( https://docs.aws.amazon.com/freertos/latest/userguide/getting_started_nordic.html ).
I followed the instructions...
