I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
My application is on the nRF52840 Dongle using ESB protocol, receiving data from an number of PTXs, . The device appears as an HID.
I would like to add Buttonless DFU, without...
Hi,
I am new here and I have some issues with Zigbee reporting implementation.
I am trying to implement a reporting feature between a coordinator and an end device, which...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
Hi all,
since new version of IOS nRF Mesh App I can't finish provisioning of my nRF52840 DK with flashed light example client.
When I start provisioning for the device...
Hi,
I am using NRF52832 with SDK 15.3 and SD 132 on our custom board ( VDD 1.96V ). I started with with the ble_app_template example for our application. Upon measuring...
Hi Nordic
I am using saadc example now, my device output voltage range is -4v~4v.
my saadc config:
VDD: 3.3V
Reference: VDD/4
Gain: 1/4
Mode: SINGLE_ENDE
i got...
Hi, I am new to BLE, I am trying to send and receive data over BLE and print them in Uart as well in both devices respectively.
And I downloaded lastest NRF5-SDK, I have...
Could you, please, direct me to any example (if available) how to manage lost bond with nRF52832/ SDK16 BLE?
Let say very common situation that will try to demonstrate with...
Hi all,
I have hardware as below:
nRF52840-DK - as an advertiser and the same type of board nRF52840-DK - as a scanner
My problem is that I want to send more data than...
Hi,
I have been going through the Bluetooth Course ( https://github.com/NordicPlayground/nRF52-Bluetooth-Course ) and I can' seem to make it work, even if copy/paste the...
Hi,
I'm using nRF51822 to develop our products. I found an interesting problem on our PCB. After I disconnected our PCB from central device, the main function starts from...
I am developing a wearable using nRF52832. I am using SKD_15.3 ble_app_uart source code for testing. And use Putty together. This source code implements UART Baudrate up to...
I have been using fds for flash saving and read. I have used fds_record_write(..) with no errors and proper readings on the just before performing a 4th fds_record_write(...
