Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
Hi,
As the tile says, I'm using BPA600 capturing mesh logs and analyze.
Since BPA600 needs to configure "MeshOptions.ini" to be able to decode the logs, it needs "IVindex...
Hi
I would like to debugg my Nordic (nRF52832) custom board at 1.8V with a 6 pin Tag-connect connector ( see here ) and have a couple of questions regarding...
Hi,
I'm trying to compile a simple example (light_switch_dimming_server_nrf52832_xxAA_s132_6.0.0) for Bluetooth mesh with Segger embedded studio. I'm having a hard time...
Hello,
I have a twi module developped using sdk v13. I want to upgrade it to the sdk 15 to integrate it to a mesh project.
I changed all nrf_drv functions to nrfx same...
can I make indoor localization with nrf52840 DK board without an android app,
suppose I am using 3 devices for localization of the 4th device, and I need to get RSSI of...
I want to make infrared transmission and reception function with nrf51822.
I want to know how to make TImer part using NEC protocol.
Tell me how to implement this feature...
Hi,
I am working with nrf52832 DK,softdevice s132.SDK15.
I was following "nRF_Sniffer_User_Guide_v2.0.pdf" to set up nRF Sniffer.
But in the Wireshark Application under...
Hi there,
This is a general question about addresses types in Bluetooth mesh and specs:
As far as I know, Bluetooth mesh specs talk about the 32767 nodes in the theoretical...
Hi guys,
Can someone provide the documentation if it exists the proper way to migrate from the SDK 13 to SDK 15.2?
should I migrate from SDK 13.0 to 14, 14.0 to 14.2,...
I am using multilink (version doesn't matter)
In main.c, certain variables, i.e., m_lbs_c, are declared and used in, i.e., led_status_send_to_all.
BLE_LBS_C_ARRAY_DEF...
