Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello.
I try to periodically updated data in my characteristic that way:
As soon as I connected via "nRF Connect", function " sd_ble_gatts_hvx" returns: NRF_ERROR_SVC_HANDLER_MISSING...
Hi all ,
I have SHT31 and I can read Temperature and Humidity value by NRF52 . But I want to create 1 service for display it on smart phone with the RH (name: Humidity,...
Hello,
I would like to measure the voltage of circuit GND by using the embeded SAADC of nRF52832.
But unfortunately I have no vacancy of GPIO to connect GND.
Could you...
I have set up a nrf52840 kit to upload data to nrf cloud via bluetooth but the data on the cloud is displayed as a hexadecimal number(1,2,3,4,5,6,7,8,9,A,B......) I want to...
I am not seeing a transition to BLE_ADV_EVT_SLOW. The transition I see goes from FAST to idle, without a transition to slow, from the configuration I don't expect to be in...
I am trying to implement a timer using nrf_drv_timer.h and nrf_timer.h, however, the handler never gets called.
I first create a timer, then define a timer handler and finally...
Hello everyone! I am trying to program a nrf52832 sparkfun board through a nRF52DK. I have already gone through the pin connection guide succesfully and I can flash succesfully...
Hi there,
I could program the HEX file to nRF51DK via nRFgo studio successfully and the board seems to work fine as well. And then, I try to read back the HEX file from...
I am just wondering if it is possible to use the 52840's USB interface to create an R/NDIS type interface . The intention is to maybe create a WIFI/Cellular based Network...
Hi,
I am testing ble_app_att_mtu_throughput in SDK 14.2.0 between two nrf52832 DK board. One is act as a central and other one peripheral. I am placing these two boards...
Not a question, just to tell you that in ble_gatts_attr_t Struct Reference, documentation of « uint8_t* ble_gatts_attr_t::p_value », a « @ref » Doxygen markup has been produced
I have one pca10040 board, I want to realize the data transfer between the nrf52832 and the PC by BlueTooth, I use python3.5+PyBluez. When the nrf52832 is running the "ble_app_blinky...
The following lines are copied from the SDK15.0 documentation:
<pre>
Supported boards:
- PCA10040
- PCA10040E (nRF52810 emulation on PCA10040)
- PCA10056
- PCA10059 (support...
Hi, we are using
'iOSDFULibrary' , '~> 3.0' for firmware updation process. we are getting "DFU not found" error when device is already in dfu mode at the time of update...
