Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I'm trying to run the DFU buttonless example however this line crashes the app:
err_code = ble_dfu_init(&m_dfus, &dfus_init);
UPDATE:
Looks like this is causing the...
Hi all,
I am learning about the security mode level in BLE. Understood that BLE 4.2 added additional method which is called numerical comparison.
When I tried the...
I am searching for example on pstorage, I want to store data in flash using pstorage, mainly I want to know which files I need to include for using pstorage.
Hi all,
can we configure systick on nrf52840 to genrate exception every 1msec.
Tried doing the same but not able to observe correct value.
These are my configuration...
Hi. I need high data transmission rate(>500 KBps) over a long range(about 1000 m). Can you suggest me the best device according to my req.
Thanks & Regards
Utpal
Hi,
I have configured systick for 1msec value with Ticks=64000. When I read the systick calibration register value, the value is 0xc0000000. This indicates the Tenms register...
Hi,
is it possible for the NRF52832 to have an external I2S MCK clock when being in master.
Because I am working with a DAC/amplfier which will play some sound files from...
Hello.
I'm newbie in nrf51 world so maybe my questions will be a bit stupid.
I bought few nrf51822 modules on Aliexpress. Photo: www.dropbox.com/.../77_1.jpg
I bought...
Hi,
When trying to install nrf5x Command line tools 8.4.0 (under windows xp), the setup program ends with an error (see nrf5x-cmdlinetools.log ).
It seems to do with...
I want to be able to read my i2c and program logic flow within the BLE application but when I try to set breakpoints it causes the cpu to do a hard reset. How can I capture...
I have an nRF51822-DK board and so far I could not properly grab from the examples a simple thing: is there any specific initialization needed when coding?
For example...
Hi All,
I'm currently developing a network where I would like to use nRF52 SoC. The nodes in the network must be able to extend to over 100 and must be able to multi-hop...
Hello,
I've taken the example from the SDK 12.0.0 for RAM retention. I've added additional NRF_LOG statements to check if the RAM retention is happening. I do not have...
Hi all,
In the Data sheet ,i saw it is a short cut register . It is available for all the peripherals with offset 0x200.
Can you share more information about it, like...
