Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
Hi I have built a custom NRF8001 board and I'm debugging a problem.
The main microcontroller works fine (atmega32u4) but the RDYN line never goes low to start the setup...
I am starting development on the nRF51422. I noticed that for the non-ANT sample code (blinky and UART), a gcc makefile and windows batch files are provided for compilation...
Hi,
Does the heart rate demo in SDK v4.4.0 work with SD v6.0.0? I'm using the QFAAC0 revision of the NRF51822. The demo works fine with SD v5.2.0. Is there anything special...
So far I haven't run across any code examples that will switch the BLE (S110) stack in and out. I'm looking to test enabling and disabling of the softdevice to see how that...
