Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
HI,
I have a product which scan for RFID card through NFC and Mobile Device through BLE after nRF52840 MCU was wakeup.
If I scan NFC and BLE scanning separately, everything...
Working with a Pinnacle 100 using an NRF52840. I have a HMI with a TTL serial interface. I have verified I/O on the HMI itself via a TTL/USB converter to Tera term, but having...
Hi! I have a fleet of narrowband and cat-m devices around the world. I want to determine their rough position by using the cell tower information. I tried CellLocate from...
I have a board with the nRF52832 and a board with 12 SK6812 LEDs on it in the shape of a ring. I have code that sometimes will display the correct color on the ring but other...
I think the NFC pin is set to the default state on the nRF52832.
Currently, I set CONFIG_NFCT_PINS_AS_GPIOS to 1 to use it as a GPIO pin, but is there a way to make it the...
Hi, I'm using nrf52810 ,nrf connect, zephyr, vscode extension. I’m having trouble using both UART0 and the NUS UART service. Here’s a snippet from my overlay file:
/ ...
Hello everyone, I'm trying to perform a device firmware update using the buttonless service on nRF52DK with SDK v17.1.0 and Softdevice S132.
I can connect correctly to my...
Hi,
I’m working with Timer 0 on my nRF5340 DK and trying to set up two different intervals: one at 1 second and another at 60 seconds, each on separate channels (COMPARE0...
If I am to do a custom SPI Slave driver to achieve ultra low latency handling and would like it to coexist with NCS / Zephyr, is there a document describing this ?
E.g....
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it is iBASIS...
