I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I need to set the connection interval to 7.5 ms. The main.c has the corresponding macro: MIN_CONN_INTERVAL but it seems to me that it supports only integer values...
Please...
When building examples targeting the thingy53/nrf5340/cpuapp board target cmake is run twice, on a fresh build. Then once the build is finished, without modifying anything...
Hi,
In the past we had quite some issues with moist in nRF9160 issues (likely due to bad storage at our PCBA partner). We are now baking all nRF9160 always at 125 degree...
Hi all,
i am currently developing applications for the nrf54L15 for science. We ordered nrf54L15DK and everything is running fine. As we would like to switch to public availabe...
Hi,The Nordic Team
I am developing the Matter over Thread product. I have defined a Bluetooth transport protocol, and now I can receive data. But now I do not know how to...
Hello Nordic Team,
I’m looking to build on a BLE Scanner(Beacon functionality) + Peripheral features on my application using the nRF52810 device, but I’m facing difficulties...
I've been unable to get a SPI MOSI pin to output data on nRF54L15DK using Nordic Connect SDK v3.0.2. SPI transactions report success, and the SCL and CS lines are clocking...
I'm trying to use an ILI9341 display with nRF52840 in Zephyr (v4.1.99). The build fails with multiple errors about missing Devicetree properties when compiling display_ili9xxx...
Hi NRF team,
I am currently working on the microphone module in zephyr RTOS. I am using the zephyr sample code for stereo. I am reading the stereo microphone at every...
The npm2100.overlay file generated by the nPM PowerUP app (v2.1.1) appears to have errors, and does not compile with the nRF Connect SDK Toolchain v3.0.0 in Visual Studio...
What happened to embeddedcentric.com? NOTE: They made use of Segger Embedded Studio (SES) for the training. Can SES be used for this training, or only Visual Studio Code ...
Hi,
nRF54L15 DK + VSCODE + nRF connect for VSCODE,
I test example peripheral_uart, when click debug to start debugging with GDB，it show error：
Starting: "C:\Program...
I have code working for interfacing the nRF52 DK board to a SSD1309 based 2.42” OLED display.
The problem is with getting the correct indexing for lines and columns.
Can...
Hello,
we are experiencing rejection from the network by receiving cereg notification. Modem afterwards stops attempting to connect to network. Which results in application...
I had used nRF52840 DK sometime ago and successfully tested it with different codes. But now when I connect the kit to the PC, it is not getting detected by the same PC that...
