Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have an NCS project compiling and running for nRF52840 (nrf52840-DK) and am attempting to transition this project to nRF5340 (nRF5340-DK). (Prior to this, I tested the nRF5340...
I've just received a new NRF5340-DK and am trying to compile and test the 'peripheral_uart' sample.
I'm using SDK 1.50.
When I loaded it into Segger via "Open NRF connect...
I have a problem with nRF5340 :
when building with west build -bnrf5340dk_nrf5340_cpuappns -p so I have a clean build and flash after that with west flash everything is...
I have an nRF52840 acting as a SPI slave to another processor. If I put the nRF52840 into a deep sleep mode, how can we wake it back up over SPI? I typically have only seen...
Hi Team,
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
chip - nRF52810
I would like to reduce the power consumption during systemON by disabling unused...
Please note that I am a new developer.
I am currently testing on a nRF52 DK on Windows.
I want to flash my application (which has a SoftDevice) and also write manufacturing...
Hello,
We have a lot of boards (more that 5000) witch embedded a nordic NRF51822 to scan beacons.
the person who designed the card did not plan any bootloader on the NRF...
Hi there,
I'm new to using an ATE and a NRF52 and I'm trying to use an ATE array with telnet commands to program firmware on 10 devices. After the firmware is applied, our...
Hi,Nordic!
I have a strange problem. I program custom boards. I can successfully program the application core with segger, but I can't erase and program the network core...
SDK 14.2, NRF52840, S140, NRF Connect for iOS iPad (v2.4.8)
We are sending a value to a characteristic as a request using the NRF Connect app, and then our NRF BT device...
i use nrf 52832 for scan BLE adv, sdk 12.3 ,
for reduce the missing scan signal, I use three ble_central BLE to scan, so i want set one ble_central to scan one fixed single...
I'm using the Serial_LTE_Modem application (nrf source version, zephyr v2.4.0-ncs1, mcuboot v1.6.99-ncs1, mcumgr v0.1.0-ncs1 ) with version 1.2.3 of the modem firmware. I...
Hi Nordic Leaders,
I need to complete nRF5340 based C++ Software simple solution for ONLY Data Transmit, Receive and Data Store on Flash for our Tier1 Medical client by...
I'm working with an nRF52840-MDK from MakerDiary in the nRF SDK for Thread and Zigbee. I would like to power on an LED when the chip is powered on. Here's a snippet of my...
Hi Guys，
According to the MESH document, there are two ways of node provision: PB-ADV and PB-GATT (smart phone) . A provisioner provides the unprovisioned device with provisioning...
