We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
Hi,
I want to identify the specific provisioned node among all n number of provisioned nodes using nRFMesh app.
Does any event will be appeared in sdk, after provisioned...
Hi, I am begginer, I work with SES, Mesh_v5.0.0, nRF5_SDK_17.0.2, and s132, SD v7.2.0. I started it two weaks ago. :)
I tryed the examples, Light switch , with server and...
Does Nordic have an example SW for transmitting and receiving data in BLE 5.2 connectionless isochronous communication mode? Is there a SoftDevice that would support this...
Hi, good morning , i am just wondering is it possible to send and recive data through ble faster than the coded examples please as i am sending gyrodata and its taking about...
Hello - I've google'd around a bit on this unsuccessfully...
I've successfully provisioned and configured an nRF Mesh network with mutliple servers and a single client,...
hi, I am working on the nrf52832 device, I have implemented the push button and I am able to detect button push and release but I want to notify the app when the push button...
Hi,
I am trying to interface nrf52832 with LoRa transceiver module sx1262. Can anyone please provide some sample code to check basic Tx/Rx of this chip. I am unable to find...
Hi,
I am looking for an example that uses the eDMA with the TWI in the 15.2 SDK on nRF52840.
My idea is to read out an external sensor using the TWI with as little processor...
Hi,
I would like to know how to set the service to NB-IOT Cat NB1,
and how then to set the UL subcarrier spacing to 3,75 KHz,
and how to fix the power to 23 dBm, not...
Hi We use INCE sim card in both Denmark and Sweden on our custom product. My main thread basically doing this:
lte_lc_offline ();
lte_lc_init ();
lte_lc_connect_async...
