Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello, i'm currently working on my Bachelor Thesis using Makerdiary Board. I recompiled the OpenThread Libraries to get the CLI working on my Board. I need to read out sensors...
Hello,
I'm trying to use UART0 for communications between the nrf52840 and another microcontroller, while also using UARTE1 for debug communications between the nrf52840...
Hi.
I'm trying to combine TWI sensor and BLE app UART examples.
I already tried putting parts of TWI sensor example in the BLE example, but it gave errors on missing...
HI everyone,
I have issue relate to ble_lbs_init(ble_lbs_t * p_lbs, const ble_lbs_init_t * p_lbs_init) function.
issue happened when i call: err_code = sd_ble_uuid_vs_add...
I am new with nRF9160, just bought a nRF9160 DK from overseas, but I use it in China, two questions come up.
1. Is it working with China celluar network?
I tried the Basis...
Hi,
I'm trying to make the softdevice controller work on NuttX RTOS. I followed the SDK example code to reproduce initialization. All calls are returning 0 (no error). However...
Dear Sir,
we're developing a Ble keyboard with 52810. the product needs to detect what kind of operating system and have different behavior therefore. but i don't know how...
As below, BLE Data RX works fine, but TX doesn't. When does this happen?
Currently BLE connect/disconnect and RX is working fine. The power does not turn off due to this...
Hello: I am trying to design a project about a type of sensor powered by high accuracy battery which is using the nRF52832 chip in a custom board. To use the battery energy...
Hi
My requirement is to upgrade the application firmware on the nRF52840-DK from another processor using SPI interface, and I am trying to understand the code to plug-in...
I'm developing a beacon application using the Fanstel BT832AF, which uses the nRF52810 internally. This unit is mounted to a custom board, but before raising a private ticket...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
