Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
Looking at the code of function nrf_log_frontend_dequeue, in nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c:716, it seems to me that the code chunk...
Hello!
I'm trying to implement a thermostat cluster handling. I've managed to implement read/write thermostat attributes handling using zigbee device callback. The problem...
I am trying to design a remote control for my garage door and I need to develop a low power remote control that talks to my Thread garage receiver.
I have looked into OpenThread...
