Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am trying to find where to submit bugs against the pc-ble-driver. There are two major bugs I have found
saved CCCDs (in a bonded connection) do not get restored when...
Hello, everyone
I use NRF52840 to configure TWI to operate the sensor, but I don’t understand it.
Can the hardware TWI of 52840 be mapped to any IO?
Or is there a fixed...
Hello!
NRF52832 is used as a central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
On android phones...
when I use usb to transfer, i fine many datas are lost.Is it because the DMA size is too small?Where can i see the dma size?(In nrf52833/examples/peripheral/usb_cdc_acm )...
I am trying to connect a SPI device to the external connector pins on the nRF9160dk board. I believe I know the name of the SPI device and the pin connections from the device...
Hello
I'm trying to print out several sounds with one buzzer. To do that, I need to be able to change the frequency.
PWM was initialized and reset using code. An attempt...
OS: Linux Ubuntu 18.04
Compiler: Gnu ARM embedded
HW: 2 nrf52840dk boards
NRF SDK: 16.0.0
I am trying to send data using L2CAP CoC. I have looked at the ots example...
Hello,
I am trying to get familiar with the DeviceTree macros and started experimenting ...
So, in the light controller example main.c I replaced this macro
#define...
Hi Nordic,
I bought an nRF9160 DK for use in the UK on o2's network, but the signal in my home office is poor resulting in me having to go to the window to get connectivity...
Hey,
I am using ibasis simcard which comes with nordic thingy 91. Now i used 10MB which comes free for testing.
Now due to this, i am not able to send data to nordic cloud...
Hi,
I'm working on a project with nRF51822QFAA on nRF5_SDK_12.3.0.
I'd like to ask if the app_button library uses all four GPIOTE channels?
In my project there are...
Below is the output from a 'bluetoothctl' session for one of my thingy:52's
This is running on a raspberry pi 4 using Ubuntu Mate 20.xx
The output below is using command...
In beacon example code the RSSI value is 0xc3 while converting to decimal it giving 195 and in comment line it is mentioned as dbm.when converting this 195dbm to milliwatts...
hi,
The Fanstel BT832 has a nRF52832. It has TX on P11, RX on P12 for standard uart. I need however rs485 and so need to add a DIR (output) pin. P11 and P12 are not on...
In the mRF24L01+:
Unlike MultiCeiver mode, I have one TRX and multiple PRX units sending back ACK payloads.
In the PRX, what is the purpose of the PPP field in the W_ACK_PAYLOAD...
