Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
Hello,
We start using of our BLE devices with more or less permanent connection with our central BLE device, it was needed for Alisa connection.
BLE peripherals are old...
Hi,
I am a beginner in nRF52840. I want to add a channel hopping feature in the 802.15.4 example .
As per my understanding of source code, we can set the channel number...
I am looking for a way only a known/trusted device can connect and write/read information from my device. Filtering by address(white-listing) is not feasible. So what is a...
Device:
Peripheral only
Peer Manager and Bonding working
S140 radio
nRF5 SDK 15.2.0
Rigado BMD-340 module
Central == iOS devices
Our nRF5 module is controlled...
Hi, I'm on last step of developing, but I have this critical trouble. For the project, I started from ble_app_buttonless_dfu sample of SDK15.3. I added some peripheral (one...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
Hello,
I am using UART to receive data on a nRF52840 DK.
I have written some code using the Serial Port Library.
I have attached snippets of the code dealing with the...
