Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hello,
I have the NRF52 DK with a PCA10040 designation. As instructed, I connected the board to my computer via the USB cable. The original demo on the board worked fine...
Hi,
I need to implement a simple external interrupt triggered by another IC on a nrf51822.
After searching the devzone I found the example in the GIT repo ( github.com...
My code is roughly based on:
devzone.nordicsemi.com/.../
I'm using SDK12.2, softdevice S132. The relevant parts of code are:
static uint8_t bapi_adv_data[14] = {...
we are facing issue of "application program" hex file generation, which is different in two machine . we are matching setting of both machine , we found the difference in...
Hi,
I've got a problem with nrfutil package on Raspberry Pi with Python 2.7.9 and pip 1.5.6 included to raspbian distribution.
I'm writing like below:
pi@raspberrypi...
Using SDK 12.1.0 with flash containing data from a previous version of software.
The pages_init function in fds.c does no have adequate protection to prevent writing to...
Hello,
I have followed a couple of the posts on the devzone on how to increase the MTU and add the DLE support such as this .
However, whenever I send over 20 bytes...
hi, i have a SIM800L Core board which is using UART protocol to communicate or to send At commands. so that i am using BLE_APP_UART example to set AT commands to SIM800L....
Trying to follow this tutorial using KEIL 5.23, J-Link 6.14b and the DK.
I am getting linking errors like this when compiling:
What did I do wrong and how can I fix...
hi,
i was looking for example of two nrf52 communication. One is central of course and other one is peripheral. But i have following doubts.
If one is central then...
What is the right way of stopping and then subsequently re-starting SAADC?
Using the saadc example, I want to be able to stop saadc when a certain pin is grounded or when...
Hi,
I just found the following example:
infocenter.nordicsemi.com/index.jsp
There the baudrate 115200 is set by default. If I calculate the bit rate (8 data bits one...
Hello,
I use two NRF24LE1 emission and reception when I use a simple ACK is good but with ACK payload, there is a problem,
I do not really see where you can help me,
Thank...
In an answer to this question about current usage of pull-ups here , RK and Vidar comment:
Is the GPIO you have configured as a pull up, being pulled down? If so you...
How to save data persistently(non-volatile) to nRF51 core not effected by powering off and on?
(How to save static data persistently without deleted when the core is turned...
