Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello,
I would like advertise for an unlimited time.
Why value 0 in ble_gap_adv_params_t::timeout don't work ? Device don't advertise anything. It works fine with a positive...
In the nrf_drv_gpiote in SDK 11.0, I can only find a function to get the address of the out task for a gpiote channel. Shouldn't there be a similar function to get the addresses...
I am working on nRF51822 ble_app_bps and I want to use Estimote SDK to monitor beacon on the background.
I also changed UUID, Major, Minor value: UUID.fromString("00001810...
Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
Hello Nordic Support Team,
We have a product that uses nrf51422_CE_AA, Revision 3, 256KB ROM, 16KB RAM, PCA10028, SDK 8.0.0, S110. Since there are more than 7000 devices...
I'm trying to get the default SDK v12.0.0 BLE App UART running with SoftDevice S130 v2.0.1, with minimal customization (I just enable the Peer Manager module in sdk_config...
Hello,
I am using i2s through the driver : "nrf_drv_i2s". After playing a song, I have a residual current consumption about 1mA unless I call nrf_drv_i2s_uninit every times...
Hi everyone!
I flashed an application with the help of DFU bootloader. The application runs for the first time . The application contains a service that lets the application...
Has anyone had the problem recently of trying to make or debug from within GCC and hitting an exception immediately? I believe I picked up an update to Eclipse because after...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hello,
I am using ble_app_template project. I want to add uart in this project. So I am referring uart project from peripherals. Now in ble_app_template project under nrf_drivers...
Hi,
recently I experienced a strange behavior on the nRF51 chip, that is at a certain point some gpio lines remained held high, even if the firmware set them to low (both...
I clone the repository on GitHub, which is the accompanying code for the Application Note nAN-36 "Creating Bluetooth Low Energy Applications Using nRF51822", in the nrf51822...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
