Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
In the nrfConnect SDK I can see just one example for a I2C sensor - BH1749
I want to modify this for other I2C sensors.
However the README does not explain how to make...
I would like to calculate how much time my device does fast advertise and how much time it does slow advertising?
Is there a way to check this in python script?
Hi,
The SUPL Client library version 0.6.1 still links to the old BSD Libary, and will give a link failure, when building any application with SUPL Support
CMakeLists.txt...
Hello,
I am working to verify custom services on my device using nRF52 dev kit.
I am using HR collector example code as reference. I am able to read the custom service...
Hi,
I am trying to add the beacon Eddystone features to my DFU buttonless application.
After compiling the code, I wrote the softdevice, the bootloader and the application...
I am integrating a sensor on SPI 1 with cellular but device get stuck in CPU idle when first transaction of SPI is made?
I am using nrf9160dk_nrf9160ns as board configuration...
Starting with the dev kit, where I get correct behavior. First, I make sure the RESETREAS register is all zeros. I do this like so: NRF_POWER->RESETREAS = 0xFFFFFFFF; while...
Hello,
I am using nrf9160 and want to test the just simple SPI function. The code that I found from github( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples...
Is there a way to set duty cycle before app_pwm_enable(&PWM1) call ?
Or some other simple way to switch on and off a passive buzzer signal without every time at off/on cycle...
Hi:
We're working with a 3rd party testing agency for our product that is using SDK 11 with S132 Softdevice 2.0.0.
If I understand correctly, the SDK allows up to 6 transmit...
I am trying to implement a system / integration test of a BLE device.
I would like to use the nRF52840-Dongle in my PC and use the PC-BLE-Driver for Cpp as the Central....
As you could see from the below image, the SCL signal at 400kHz is NOT a good square wave.
1) Why & how to solve it, please?
2) Also, why SCL is between 0.4V to V_DD=3...
I am now pulling my hair out with these drivers ... I'm trying to do what I think is the right thing and use the new nrfx drivers, but it's really not easy.
So this started...
Hi, I am using Zephyr's BLE for transmission In the peripheral, I record the time when I send the notify to cental (start time) Then when I received the central write_without_response...
Hello,
I have a peripheral that is connected to nRF52832 using I2C, in which I want to send some file to its memory. However, for sending this file, I need to stream it...
