Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Maximum current consumption for each of the pins in the respective modules of PWM, TWI-I2C, TWIM-I2C, TWIS-I2C, SAADC, UART, SPIM, TIMER, RADIO-2.4GHz under the operating...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
Dear Support / forum,
After reading the user and API guides, browsing other posts, and playing around with the ack-payload example, I think I now have a pretty good understanding...
Hi,
I am having a issue with building an application in IDE for nRF9160
Application : Asset tracker
I have been able to build this "problemfree" before, but this morning...
Hi~
I am developing door sensor system using nRF52840.
Currently for power consumption, sensor (nRF52840) is system off(NRF_POWER->SYSTEMOFF=1).
nRF52840 can wake up...
Hi, I have 8 peripheral devices each one has at least one sensor attached to it( peripheral will be nRF52xx), the sensor has a sampling period of 8ms. I will be using android...
Hi,
In BLE mesh v3.1.0 I see a file debug_pins.h. For what these debug pins are used and can I disable it for my custom board?
And one more thing related to PA and LNA...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
