Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I measured the output power over all the channel, see graphics below. It is not much, but i still would like to know why the output power drifts over frequency. Is this by...
Hello,
I have two nRF52832 (BL652) modules setup and connected through an RF cable. I am feeding the peripheral radio (2x) 174 byte packets every 5 ms. On the central, I...
Hi,
nRF9160 mqtt works with ipv4 by using "ncs\nrf\samples\nrf9160\mqtt_simple" application.
Now NB-IOT network which we are using is faced out the IPv4 and moved to IPv6...
So we have a great set of 52832-based set of products in the field that negotiate, agree to, and support MTUs larger than 23 bytes. Nordic's is incidentally one of the least...
Hello everyone!
As far as I've read in the manual, Power Monitor allows to export measurement data to file and use the for further processing. I'm using Power Monitor v2...
Hello,
I am using ublox B201 for my project which is based on nRF52832 SoC & with use of SDK 12.2.0.
So i need to know which IDE supports nRF5 SDK 12.2.0 ?
As segger...
SWDIO,SWDCLK,VCC AND GND have been taken out from the nrf52810 ic and proper connections have been made to the jtag end of the j link device (connecting all grounds also)...
Hi,
I am trying to understand one thing about the att_mtu_throughput example.
What it does in the char_notification_send() function, which is shown below, is that if it...
While trying to upgrade my application from v0.4.0 to v1.0.0, I bumped into this issue. I am using CONFIG_POSIX_API primarily for the clock functions like clock_settime and...
Hello,
I've been trying to use latest nRF5_SDK_15.3.0_59ac345 from the website (couldn't find git repo for this - apparently there's none).
ble_ant_app_hrm example project...
I have custom board with nrf 52832. I am using SDK 12.3.0. and soft devices s132 V3.0.0 to transmit advertising packets with advertising interval 1s. I have written simple...
Hello ,
I recently bought sparkfun's nrf52832 breakout board. It comes with preprogrammed serial boot loader. How ever after flashing code from nrf52 DK into my nrf52832...
Hi,
I would like to use LE coded layer feature while sending beacon packet on primary channel.
According to table, I should use ADV_EXT_IND packet type to send beacon...
