I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Dear friends,
In the Power Profiling Application (an example of nordic SDK), the priority of the application timer is set to APP_LOW(as shown in the pic below).
However...
stdio.h defines vsprintf and _vsprintf, and suggests using _vsprintf if you want to save on code space.
extern _ARMABI int _vsprintf(char * __restrict /*s*/, const char...
As per the Bluetooth Spec (v5.0) Page 2323-2324, it seems that LE Secure connections pairing supports 1-way OOB. See section of text below.
If OOB communication is possible...
Once GPIO is pressed (shorted to ground), I want to change the value of UUID or Major/Minor number
If not, the device will continue to advertise the previous values
Hello,
I am working on a custom project with nRF52832 using SDK14.2 and s132_nrf52_5.1.0.
Now I am trying to configure and use RTC2, and face the problem that ble_stack_init...
Hello everyone,
after hours of python module installation, I was able to run the PPK with PCA10056. I have cut the SB40 and used an external pwoer source with 2,5 V. I have...
Hi I have two problemes, I do not know where to start, so if someone has an example, I would like to see it. The first thing is if someone has an example about using pwm to...
When registering a base UUID with the SoftDevice via "sd_ble_uuid_vs_add", a uint8_t is returned which (per the ble_app_pwr_profiling example) is intended to be the "type...
SDK 14.2
I try to use the watchdog using this code
static void nrf_wdt_event_handler(void) { NRF_LOG_INFO(">>> nrf_wdt_event_handler") }
int main(void) {
...
nrf_drv_wdt_config_t...
Hello , I am working on the development kit nrf52, i want to know how i canget the value of the RTC overflw and then how i can reset the RTC to zero.
thank you in advance...
We are developing a React Native mobile application for iOS and Android, making use of the react-native-ble-plx library to interface with the BLE UART service from the examples...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
