Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
main.c I'm using S120 softdevice with nrf51822, I want to use S120 as central and peripheral devices.
When I received my beacon data then switch to peripheral for advertise...
Hi!
nRF52, SDK13, S132.
I work in central mode and need make
ble_nus_c_rx_notif_enable()
But in the code drivers I only have tx function. In a SDK9 for nRF51 I...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
What I am trying to accomplish is to establish a connection between an iPhone (device 1) and an NRF52 (device 2), then sniff the data sent between them from a third device...
Hello,
I have designed a custom board with NRF52832 IC which controls vibration motors. And I am turing on vibration motor from n-channel mosfet as shown in the image below...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
On a custom board with an nRF52832, I have some LEDs I'm driving from the pins 9 and 10. One or both of these pins are used for the NFC antenna unless you configure them as...
I am trying to understand the whitelist feature by following the HID Key board peripheral example on S140 v5.0.0.-2_aplha on nRF52840 dev kit. I am using iPhone SE with nRF...
Hi all,
I'm trying to return a write response in nRF sdk but so far no success.
Actually I'm still scratching my head to figure out how characteristic write works exactly...
I am trying to build and debug the Mesh v1.0.0 light-switch server example and getting a
cryptic error when launching the debug.
My environment is Segger v3.30 on macOS...
