Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
Hi, there
NRF51822
SDK9.0.0 and S110
How to subcontract in uart nus mode to ensure that each packet does not exceed 20 bytes and is sent as quickly as possible...
Wakeup from system off (not WFE) )will cause a system reset and hence will reset almost all of the peripherals (exceptions are RAM and few registers). RTC will also be rest...
Hello,
Is there a BLE only DFU application like that available on Android? The Android application works fine. The windows version needs a serial port to perform the same...
For synchronizing an external sensor i need to output a 32768Hz clock at a GPIO pin. For this case i want to use LFCLK from the external cyrstal.
My setup:
I use RTC0...
Hello,guys
I have build one application, in which I want to transmit the Image from Mobile BLE to nrf51822 and than after display on display like E-paper.
The use case...
Hi,
I use it as a translator for Google, so it may be strange in context. please understand.
I was in big trouble.
I used the nRF51822, S110, and SDK9 in my previous...
Hi. We are attempting to use the Infineon XMC1202 LED shield with our NRF52 device. The XMC1202 has an I2C address of 0x15E, instead of the traditional 7 bit address. We have...
I've tried linking the ESB library (esb_arm.lib) in Eclipse by adding it to my nRF51822 project's Makefile, but I am still getting undefined reference errors during build...
Hi
We are going to use the Taiyo Yuden Evaluation Board - EBSHJNZWZ.
As i understand, the board firmware used the Nortic SoftDevice S132
The question is :
May i...
Hello,
I'm trying to compile an example of nRF52_SDK_1 but I get this error:
make
Makefile:150: Cannot find include folder: ../../../config/receiver_pca10040
Makefile...
Hello,
I've been reading over different examples and questions on the Nordic Developer Zone but still have some questions about multiple SAADC channels.
1 - If I initialized...
I've been developing an application on the nrf51 DK based on the ble uart application and it's been working fine. I've ported it to a custom board running at 1.8V and attached...
Greetings -
I am using (the slightly out-dated) 12.3 SDK with a nRF52840. I'm also using s132 as my softdevice.
As I've been slowly reducing my RTC interrupt frequency...
Hi,
I want to activate readback protection on nRF51822, in a simple project without bootloader without softdevice.
My compiler is GCC and the const uint32_t UICR_RBPCONF...
