Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
Hello lovely Nordic Semiconductor staff (and everyone else reading this),
I have recently been working on exploring the use of BLE via Nordic chips in my employer's products...
Hi,
How to store two application image in nrf51822 flash each image size is 60kb. I have enough space
To store images but I don't know how to store. Please guide me to...
How can i reaed 32bits word using spi ?
I don't find the function to configure the SPI to read 32bit word ?
And how top start reading ? Is this function"uint8_t nrf_spi_rxd_get...
I am seriously stuck on a project. Expert help is needed.
The goal is to create a modified dfu ble bootloader with the following properties:
Target: NRF51DK (nrf51822...
I want to add nRF24L01 for nRF52832,but nRF24L01 needs to use software to ctrl TX and RX,I hope it auto.
nRF51822 can connect to PIN30(VDD_PA) ,and nRF52832 I need to connect...
I'd like to sample the SAADC at 1280Hz. The app_timer minimum seems to be 1ms (1000Hz).
If I use continuous sampling by setting SAMPLERATE then the minimum rate seems to...
Hi all,
I am trying to port the nfc_text_record to the example experimentral_central_ble_app_blinky after I am able to compile I am getting the following message on my...
Hi
Whitelist function is in ANCS sample code.
Does it require in ANCS?
Can I disable whitelist?
If yes, how many pairing times between Device & Apple OS?
It cannot connect...
I'm new to use nordic and I would like to add a new custom service (2320EE58-8654-4132-95F7-0A872AC0958F) with a custom characteristic(23200000-8654-4132-95F7-0A872AC0958F...
