Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
When the UART is configured to use FIFO , i use the UNUSED_VARIABLE(app_uart_get(rxdata));
to read a buffer from FIFO.
how can i also receive a number of bytes...
Hi,
I want to do this cycle with GPIO without interrupting it on NRF51 with BLE softdevice:
PIN1 to HIGH level
read value of PIN2
PIN1 to LOW level
Repeat...
Hello, I'd like to do directed avertising to a central which has a random private resolvable address. My idea: both devices share a pre-defined IRK so the peripheral can compute...
I tried, but it does not work.
for(int y=0;y<100000;y++)
{
if(nrf_uart_event_check(NRF_UART0, NRF_UART_EVENT_TXDRDY))
{
nrf_uart_event_clear(NRF_UART0, NRF_UART_EVENT_TXDRDY...
Hi,
We have a little issue that we at the moment need to cycle power on v3 nRF51822 after DFU.
We have determined the the reason has something to do with the whole complicated...
I attempted to add spi_master as below, but I am in trouble with link error.
If anyone knows the cause, please tell me.
*** Using Compiler 'V5.06 update 4 (build 422)...
I'm working on a project based on the ble_app_uart_c central example in SDK 12.1. I'm polling the RSSI of a Nordic beacon using sd_ble_gap_rssi_get(), and the fastest update...
I want to handle 3.3v in nrf52832.
NRF_GPIO_PIN_S0S1 -> NRF_GPIO_PIN_H0S1
Can this be this way?
If not, what should I do?
Also, Can the PWM output to 3.3v?
Hi, I use PCA10040 v1.1 and SDK12.1. My desktop environment is Windows 7 64bit.
As far as I know, the J-Link Edu cannot be used for commercial usage.
I so bought...
Hi there,
We've had our own custom controller made, based on nRF52 (Rigado BMD-300 module).
In the last half of January we'll have a baseline firmware working, but we...
Hi, sending a data packet, then sleeping (memory retention mode), then sending another identical packet causes the receiver to send back an ACK for the first and trigger NRF_ISR...
