Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
Can I remove resistor R29 (ENCHG) on the ADP536 to disable the charging function and plug my 3.3V supply into the battery connector?
i.e. use the ADP536 for the power management...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
I'm trying to get LPCOMP working in Zephyr.
I'm getting the following error:
error: 'NRFX_LPCOMP_DEFAULT_CONFIG' undeclared (first use in this function)
I can see that...
Hi, Can anyone explain what the "receiver address correlation" from 2.4GHz Radio documentation means in practice? For example, what can I do as a BLE application developer...
For various reasons we need to remove the dfu bootloader to use our custom bootloader. We replace the Nordic bootloader with a temporary one that does the clean-up for us...
Hi,
We're designing a PCB for the nRF52833. We could not find a PCB layout recommendation for the chip.
We did find one for the highly similar nRF52840: github.com/.....
Hi,
We want to buy a nrf5340 module but it came with the Rev C Silicon Revision. Do you have any errata sheet for this revision? I only find Rev A, D and 1 on your web...
Hi - I noticed an issue in the esb library as of nRF5 SDK v17.0.2 and am looking for clarification.
In the function update_radio_bitrate , the minimum retransmission delay...
Hi Nordic Forum,
I am making a media control device using the nRF52840 and nRF5 SDK. I started with the ble_peripheral\ble_app_hids_keyboard but I don't know what is the...
We use nRF52832 and SDK 17.0.2 and the buttonless secure bootloader without bonding. I don’t understand the below issue, does that apply to our solution ? There will be custom...
I have developed a BLE app on a nRF52382 which advertised those service UUIDs
and set the appearance to BLE_APPEARANCE_CYCLING_POWER_SENSOR which is 1156.
When I...
I am working on a project where I have to store the incoming UART data over BLE on the NRF52840. I am using fstorage library to store the data in flash but I am not able to...
Hi,
I have a PCA10040 DK and am trying to measure current drawn for a non-connectable beacon. After following the instructions in the infocenter about how to do current...
Hi!
This is Cemal from Turkey.
I'm new to this community and for nordic nrf. First of all, I wish everyone a good work.
I've just started a new job at a new company...
