hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
We have a custom radio protocol that manipulates the radio registers directly (on the '32) and I'm evaluating whether or not we can switch to the '33 to use it's angle of...
i have used a example of ble_app_template in ble_peripheral of SDK15.0,when code run in ble_advertising_start,return errcode 8.
i have checked low speed Crystals，it's ok...
I get error 0x3401 in ble_app_uart_pca10040_s132 (nrf52 dk, sdk17) in ble_nus.c line 95:
err_code = sd_ble_gatts_value_get(p_ble_evt->evt.gap_evt.conn_handle, p_nus->tx_handles...
Hi,
I've been using the python bindings for the pc-ble-driver and have been getting things to work, but I noticed there is no API exposed for reading the RSSI of a connected...
I am using nrf52811, SEGGER Embedded Studio and I want to use Beacon demo. I click Build and Run , it prints as below:
And I can not find the beacon device in nRF Connect...
Hello,
We are planning to buy the BWG840F BLE to Wi-Fi gateway.
https://www.fanstel.com/wifi-ble-5-iot-gateway
It has the nRF52840 module (BT840). We have the nRF52833...
Environment:
Segger Embedded Studio
nRF52840
S140
Windows
nRF 5 SDK 17
Hi,
I'm developing a device for a small side project. I need to get logs in both the...
I am trying to integrate MAX30003 drivers in spi_pca 10040 example, So that I can get the sensor readings of the MAX 30003 sensor. But I am stuck at this error.
When I...
Hi,
I am using nrf52 development kit . I connected peripheral device and communicate all characteristics using DK.
But i want read rssi value from peripheral. I didnt...
Hi,
Do do you know of any Xamarin Development being done using your development kits?
Trying to determine the best way to get up and going using Xamarin vs native iOS...
Hi there,
Just wondering why serial_uartes example has been removed from SDK17, We have to use 2 uarts at the same time.
Is it intentional or accidental ?
Thanks,...
Hi everyone. I'm using a Thingy:91 and the asset tracker application. I can compile and flash (using SES and a Segger J-Link) the application and the device connects to the...
Hello,
I read your white paper nWP-030 about selecting the decouping caps. But I didn't find any explanation why you also specify maximum values for the caps. Especially...
Hey,
I am using SDK12, S130, nRF51822;
Trying to create a DFU update for application which Also writes over a certain area in the reserve app data, in the end of the designated...
