Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, engineer:
I need to compute FFT on nrf52840, I used sdk-demo fpu-fft, I tested the FFT operation time and found that it took 2 ms，That`s a long time, Did I configure...
Dear all, I have a problem with nRF52811 GPIOTE input interrupt. I have one sensor interrupt pin at GPIO P0.30 with external pull down resistor. I am able to config P0.30...
Hello community,
I have programmed my dongle as beacon. Now I want to stick them to the wall for experiment purposes. How is it possible to power them up via external...
Hello
I am considering a product that connects several NRF52840s to a USB 2.0 7-ch HUB and works with 30 BLE devices. When reviewing a product like this, there are some...
Hi everyone,
I have one question just for confirmation.The available analog pins on nRF52840 DBK are those provided by header P2 (six in total)?
Are there any more available...
Hi,
I'm working with NRF52832 in a BLE mesh project and I'm a newbie in this filed.
Project description:
- There're 5 devices in a BLE mesh network.
- In each device...
Hello,
in the corse of implementing pairing / bonding on top of the softdevice, I was looking for examples. The only example I've found, that seemed to not use the peer_manager...
Hi,
Currently i am developing BLE communication software for Android and iOS
This software is under Ionic development.
Is there any solution for Ionic/ Javascript development...
Hi !
When i try to open gps sample and enable SUPL client support with CONFIG_SUPL_CLIENT_LIB=y, i received this alert so i cant import project file:
I already have...
Hi all, I am working on light switch example and I want to perform different LEDs have their own switch, i.e. button 1 control LED 1, button 2 control LED 2. The problem is...
Hello,
I am working on a project where I can have Voice over IP on the NRF9160 DK. I am now working with a I2S microphone ( https://www.adafruit.com/product/3421 ) at the...
Hi,
I am setting a nrf52832 for an OTA DFU using BLE. I am on windows.
After managing to run the Secure DFU Bootloader following the getting started , I am trying to merge...
I'm using s140_nrf52_6.1.1_softdevice and nRF5_SDK_15.3.0_59ac345 on a nRF52840.
We are trying to verify that, indeed, we are successfully entering and using coded phy mode...
Hi!
I've been having some issues with the ppk recently. I've been trying to measure the current on our custom board but it was showing way too much so I tried on the DK...
What are the set of commands to send data from node (router or end device ) to leader through router,(not directly connected); in openthead cli mesh build example in https...
