I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi All,
I am using Segger ISP1430603E board to program my nRF development kit. ( ISP1507AX )
With SES I am able program, debug the application.
I would like to program...
Hi there,
I am wanting to develop a custom PCB for the nRF52833 SoC. I am basing it off the nRF52833 DK! As such, most of the schematic labels are identical.
For our custom...
Hi,
When I do a secure DFU (screen dumps pasted ), it failed with error code 0x8005. It worked on WIndows 7 PC.
//==================Linux System Report
# nRFConnect...
where is UARTE configuration in sdk_config.h? According to this doc (for SDK15.3/UART):
infocenter.nordicsemi.com/index.jsp It seems I can follow the steps to enable UARTE...
Hi,
I am using 2 PCA10040 kits provisioned in the same group. I want to change the payload on button press event from client side which I can receive on server side. How...
I have a nordic kit but the dongle or the kit is not recognized by the computer. Is there a driver that needs to be installed before this will happen? I've already installed...
Hello Guys,,
I am trying to migrate my project form keil to segger embedded studio. My product is based on sdk 12.2.0, using softdevice s130 on nrf51822. I searched for...
Hi,
we have two nrf52840 which shall connect very quickly.
The scan+advertise cycle is very fast (we have no bootloader). After switching on the peripheral it is recognized...
Hi,
I run into issues working with ads1220. Its behaviour is really strange. When I test it, data output with continuous measurement is 0. In few cases, when I swap din...
I have an nRF52840 dongle that I am using to connect and read/write to a client unit. I have been able to use the nRF Connect Bluetooth Low Energy program to control the dongle...
Hi,
My product continues adv mode after connected with mobile until the amount of connection is full. By the way, there are 4 connect handle in my product.
My client use...
the nrf51822 is working as a peripheral advertising the data like
0x0201061416FFCB113C01271119359426040A6E189C000000050852545F54,
which contains three data typs:
020106...
1. Why is `libusb-1.0.dll` bundled for MacOS and Windows? Note: I'm not question this, just want to learn why. Are they not installed by pip if listed as a requirement?
...
