I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
Hi
I have some question about DFU for Mesh3.10.
1.How to update Softdevice or Bootloader?such as I'm going to update SD from version 6.0.0 to 6.1.0.
2.Because my firmware...
I am trying to port pc-ble-driver-py to soft device version 6.1. I have made changes to python code to take care of changed API signatures, new constants etc.
When testing...
Hi,
I am using nrf52832, in the ble_app_uart_c example, i want to use rc source as a lfclk,
i changed the following parameters in the sdk_config.h:
NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I have developed a custom PCB using nRF52832. It's meant to work as an ibeacon currently and consequently works in a non-connectable, advertising only mode. I will...
Hi,
I am trying to use GPIOTE_PIN_HANDLER in the master nrf52. What is the correct way to read data from slave?
Slave device is sending data using nrfx_twis_tx_prepare...
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using app_timer_create() to create low power...
Good morning developers, I want to ask you what is the maximum transfer speed (Kbps) achieved between the chip nrf52840 (peripheral) and a smartphone (central). If anyone...
As I reviewed other post, there are many similar topic.
Thus, I would like to know whether there is new tool for the application recently.
Does Nordic have development...
