Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
hi i am trying to communicate with two devices throught UART , in nrf51 device uart i get a voltage of 2.83 v with .0238 milli ampere while in gsm module uart pin i have 4...
Hi Sir,
As reference RF5x support within the Zephyr Project RTOS , we can run Bluez in Linux environment.
But do we have the bluetooth stack in windows that we can work...
Hi all,
BLE newbie here.
I have a peripheral device (iBKS105 beacon) configured with Eddystone and iBeacon protocols, emitting on channels 37, 38 and 39. I set the advertising...
Hi, I recently started to work with the nRF52 DK (PCA10040).
I'm trying to do some experiments with PWM, so I toke the pwn library as a base and tried to add the button...
Hi I am trying to perform BLE compliance test on a nRF51822 based DUT. I want to connect the DUT to the tester using nRF51 DK. The nRF51 DK will be connected to the tester...
Hi,All,
I am using nrf52832 as a slave, the SDK version is 12.3. I set the connection timeout to 10s as follows
#define CONN_SUP_TIMEOUT MSEC_TO_UNITS(1000, UNIT_10_MS...
Hi,
I'm having an issue to connect a Galaxy samsung Tab A to my ble device.
Each time i ask for a connection i get the same error.
I already succeed with others phone...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
Hi Nordic team
I have a question about Litepoint bluetooth advanced nRF5x OTA Testing.
According to the White Paper v1.0, by using the heart rate app, it is easy to evaluate...
