Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I clone the repository on GitHub, which is the accompanying code for the Application Note nAN-36 "Creating Bluetooth Low Energy Applications Using nRF51822", in the nrf51822...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards. I want to check my runtime. So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Hello all.
I am now making a central device to control a peripheral device.
The Firmware of central device is supposed to be updated by Smart Phone, like iOS or Android...
I'm currently making a device which use nRF52832 and that will integrate Capacitive touch feature. However, I'm actually a bit lost with this post: devzone.nordicsemi.com...
Hi, I use PCA10040 v1.1, Keil MDK 5.21a, SDK 12.1 with S132 v3.
I was using SDK 12 previously. The SDK 12 projects worked well.
Now I migrating to the new SDK. So...
Hi all, I'm working on SDK11.0.0 with softdevice S130 v2.0.0 and I need to update bootloader+application at the same time in single zip for these I created zip file by using...
I have a use for the pstorage module and while going over the implementations in the Nordic examples and libraries, I found a use-case of pstorage_register() in bootloader_init...
Hello,
I would like to use the PCA10028 close to the conditions of a future custom board at 1.8 V (including I/Os) but I would like to keep the ability to do source level...
I am using the 8.1.1 version of the SDK on a Rigado BMD-200 device, s110 version of SoftDevice.
The code has set APP_ADV_TIMEOUT_IN_SECONDS to the maximum (all bits set...
My main App must be able to use the soft device directly or serialisation when a external Connectivity chip is used. How can this be done? In the examples it's done at compilation...
Hello. i useing keil v4, s110 softdevice, nrf51822 ek boards.
I want to check my runtime.
So i use under the app_timer
app_timer_create(&m_heart_rate_timer_id, APP_TIMER_MODE_SINGLE_SHOT...
Looking at the nRF51 UART Example, i know that all packets transmitted over a BLE link will be protected by CRC on the link layer.
But how about when nRF51 scan the ibeacon...
Hi, I would like to use RTC1-> cc[1] using app_timer drivers. How to do this? Examples show only the usage of RTC1->cc[0]. RTC1->cc[0] has been used by ble_conn_params.c and...
