Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I have developed my custom board and my custom application based on nRF51822 and S110-v8.
It perfectly works with Master Control Panel v9.0: connection, bonding, dfu,......
Hi,
I am interested in your nRF51 IoT SDK, IoT SDK for applications using IPv6 over Bluetooth Smart.
The presentation www.youtube.com/watch describes an architecture...
I'm developing an application supporting concurrent central and peripheral connections and using the new Connection State module in SDK 10 to decide whether a BLE stack event...
Are there any modules/devices with sar certification for the nrf51?
I have a need for something that will be placed with an elastic band against the arm or upper torso...
Hello,
I am using S110 8.0 stack and 9.0 SDK and I am testing the signal strength.
Now I am able to get the BLE_GAP_EVT_RSSI_CHANGED event after I started performing rssi...
Hello,
I am investigating the on_ble_ev function and trying to get back the Connection Interval parameters set by the Master Control throught the ble_evt_t struture . Is...
Hi,
I want to use the NRF51-DK to program an external device. It worked fine so far using the J-Link Firmware. I had to switch to mbed since it is a huge mess to get it...
Dear all,
I use nrf51422 with S210 soft device. I need to read an attached sensor via TWI. The sensor returns 32 bits of data. I need to read that 100 times a second.
...
I try to build a basic ble advertising program, I'm using SDK9 and softdevice 110 hex coming with. but just by calling any ble instruction the system freeze(my led not longer...
As it was asked here and an answer was given, but it's not working.
@Vidar: I've taken dual_bank_ble_s110 bootloader example and removed all the call I don't need, left...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
hi
i have NRF51422-QFAA-R V2 ;
i want to know how connect reset pin of my jlink to it?
u see in pic that reset pin is on the swdio;
and also i want use a button to...
Hi,
I am working on the ble_connectivity example in nRF51_SDK_8.1.0_b6ed55f. A make error occurs when building this example.
Would you please tell me how can I fix...
