Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I try to use zgp api and first try to call zb_zgps_delete_all_zgpd() but I receive an error from linker:
undefined reference to `zb_zgps_delete_all_zgpd'
Is there...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am using openthread protocol...
We want to use GPIO_12 as a wake up pin. (High -> open uart, Low -> close uart) Also, we have a timer and timeout set to 500ms. When we pull GPIO_12 to high, it seems not...
I'm working on NCS 1.6.1 for both nRF52840 and nRF9160.
I'm trying to put my devices into sleep mode so i reviewed some related tickets and found following ways.
NRF_REGULATORS...
Hello,
I am quite new to NCS. I am trying to sending UART data from nRF52dk_52832 to PC.
The example is nrf\samples\peripheral\lpuart.
If I enable the example with CONFIG_LOG...
Want to realize a function: stop broadcasting after a broadcast, update the broadcast content, and then start broadcasting again after the specified timeout. How can I judge...
I am using the nRF5_SDK_17.0.2_d674dde and the nrf5_SDK_for_Mesh_v5.0.0. I am using the nRF52 development kit and I want to know if I can use the flash fstorage on the mesh...
Hi. I am working on a project and am planning to offload most peripherals to the net core; a few are listed below. Is this a bad idea? I realize I might run out of flash memory...
hello ,
During my twim0 initialization, I have configured clear_bus_init as true and hold_bus_uninit as false. But i always get hold_bus_uninit as true.
then I dig into...
Hi!
We would like to install approx. 2000 pcs BLE devices in a mesh network. The device density is quite high (2x5 meters matrix, same level, no objects).
I think only...
I am looking for a automation where in the scripts should be able to send the CCCD(Client Characteristic Configuration Descriptor) response within one second.
1.Which tool...
Hi,
On a nrf52840 running SDK 17.0.2 and Softdevice 7.2, while being connected to two devices in central and peripheral role, I observe that on the connection where the...
I'm trying to see if there is a simple way to scan for ANT packets on all supported frequencies (not ANT+, which I know is on a single channel, 2457MHz). Just for the presence...
Hello, I am currently using the logger backend to send information via UART from the nRF52811 to a PC. This works well, but only for one way communication. I would like to...
I have nRF52840 dongles that have something already programmed on it. They are encased in plastic and I have no access to the little reset button. How can I install my SoftDevice...
