I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I wanted to create a UART-like BLE channel between a desktop PC (central role) and nRF5340 (peripheral role). On the nRF5340 side I setup Peripheral UART sample project...
Dear Nordic support:
We are now applying the PTCRB, FCC etc certificatioin with China SRTC,
And SRTC need us to fill the attached application document about LTE part(nRF9160...
I have a structure that holds my configuration data for my device. When manufactured, the programming station will flash a hex file to device that has the application and...
Hi,
Please find attached my sample hello world project : It was all good and building fine on VSCode, until I "Pristine Build" the project.
Now there are compile errors...
Yesterday I tested this new code that Charlie thankfully put together for the MQTT simple allowing publishing over the UART. Problem I have now is that I'm getting an mqtt_connect...
Hi Nordic
I have some questions regarding a firmware upgrade:
Hardware: custom NRF52832
Software Version Information: SDK: nRF5_SDK_17.0.2_d674dde Softdevice: s132_nrf52_7...
Hi all,
I have an issue with integration of the AWS IoT in my source code. The example works for me. I've tried to copy&paste the example code to my project (I delete my...
Hi all,
I wanted to start developing with nrf52840DK and rust and set myself to do a simple build that would play a sound when I press a button. I purchased a MAX98357A...
Hi,
I am using VS Code 1.60.2 and nRF Connect Extension Pack.
Currently by default output bin is generated at build/zephyr/ directory. I would like to have rename output...
Hi community I'm trying to evaluate the possibilities of an application update over the air via NB-Iot. According to this post this should be possible.
I'm using the application_update...
Hello Devzone Community,
I am writing to ask whether there is any special or obscure setting (device tree or Kconfig) to enable run-time changes to accelerometer output...
Hi, Nordic engineer!
I am doing the direction finding demos in the nrf52833dk. From previous discussion with you, I learned that with parameter CONFIG_BT_PER_ADV_SYNC_MAX...
Hi support team,
The content of ICHG in Table 22, '1.5 Ω' doesn't match with R_ICHG=1k5 in the corresponding reference circuitry in PS. 1k5 is more likely correct, right...
Hi!
I made same code for SDK15 and it works. Now I want to rebuild project on the new SDK17.0.2 and same part of code doesn't work with SPI master.
For notice- doesn't...
I have seen examples of enabling CCCD by default in the forum but I have not seen anyone say it is not allowed according to the BT SIG.
https://devzone.nordicsemi.com/f...
