I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I started working on power saving. I tried running the power_off sample from zephyr but there was no change in the current. The current holds the range 30mA to 32mA even after...
Hi,
I'm using saadc library to measure the voltage on nrf52832 DK. also I'm using soft device s132 on the project. I have several questions and will list below,
I want...
Dear Team,
I am trying to use nrf53840 USB dongle as sniffer. getting following error.
Reopen device failed: Timeout while waiting for device FAC66FF88C25 to be attached...
hai ,
In my application to connect 5 peripherals with central and here i am connecting with device names
static char const m_target_periph_name1[] = "Nordic_Blinky1";...
I try to send NRF_DFU_OP_PING reqeust ,then received BLE_GATTC_EVT_WRITE_RSP message. but write_rsp.len is equal to 0,.I can see gatt_status is BLE_GATT_STATUS_SUCCESS. I...
hai ,
i my application i should connect 5 more peripherals with one central .
at first i connected with peripherals mac id , mac id hard coded in central
in central...
Hi,
Is it possible to be notified when the device is entering/exiting idle? All I can see is that idle thread calling k_cpu_idle which doesn't appear to have any hooks?...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
I want to connect and get data multiple peripheral to a single central device.
I used this example https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
...
I can't figure out how to respond to a custom Zigbee cluster command, let alone send a custom response. Is there any example on which I could understand how to send a command...
Hi!
we're just finishing the layout for a custom nRF52832 board. On the custom board we have a connector for SWDIO and SWCLK to flash the firmware. Can we use theese 2 pins...
Hi,
I'm trying to familiarise myself with the available crypto functionality on the 52811 and have managed to get basic AES-128 block encryption working using the ECB peripheral...
Hi,
I am using pc-ble-driver-4.1.1 to receive BLE peripheral Device 240 Bytes notifications. And I used "pc-ble-driver-4.1.1\examples\heart_rate_collector" as starting point...