I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I use the template for pairing and binding. For the first time, after binding, for the second time, I bind again, prompting to reject binding. How can I match and bind many...
Hi,
I want to compile and run Mesh examples. I tried the Light Switch client, server and the Sensor server examples. All of them fail when the linker is invoked. All of...
Hi everyone!
I'm new in Nordic DKs and I have a new Nordic Thingy 91, I understand that it uses two chips: nRF9160 and nRF52840.
Maybe this is a silly question but, can...
I have a custom beacon application that is mostly idle. Before adding a timer, the current consumption was 3.2uA. After adding the timer, the current consumption jumped to...
So far I've use the nrf gatt module for setting MTU and DLE and seems to be working, however this module does abstract packets and maximum tx time in a connection. There are...
I have incorporated the DTM example into my application. It works as expected when I set the NRF_POWER->GPREGRET and then perform a reset sd_nvic_SystemReset() , then enter...
Hi,
https://devzone.nordicsemi.com/f/nordic-q-a/67024/nrf9160-questions-related-to-immutable-mcuboot-application
From the above thread i learn that MCUBoot is not that...
To get the GPIO binding I can use:
device_get_binding("GPIO_0");
1. I would like to know where in the documentation it lists the strings you can pass to that function...
I am debugging the GPS function and referring to the sample code of the official GPS. As for the code of reading GPS data, I have a question that is the way of obtaining GPS...
Hi,
We are facing some issues between our ble devices (ble version 5) and android mobiles using nrfsdk ("Android-BLE-Library") library. (Version 2.2)
We are able to connect...
I have used two sample applications light / light_switch from bluetooth mesh to get a device with 2 elements:
- generic on/off clent
- generic on/off server
I want to...
Dear Sir,
The target has a non-secure bootloader on it, I'm trying for DFU which has a secure bootloader pkg only. After initiating the DFU, nrf connect app sends successfully...
Dear sir,
Thanks for your help.
In the working state, the input voltage of the battery may drop from 3.0V to 0.4v or even 0.0V. After charging, the voltage will quickly...
Hi,
I am using the Power Profiler Kit (Rev. 1.1.1.) with Power Profiler app (v2.3.1) to measure power consumption on an external DUT. The issue I am facing is negative current...
