I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
Hi,
I would like to run the radio_test example on an nRF52811 chip for certification purposes.
What changes are required on the latest sample code and project to get it...
Hi all,
Is there any example to discover the custom UUID services with pc-ble-driver c/c++? As far as I understood, the ble_db_discovery is not supported for this driver...
Hi,
i am trying to Set TX power level from application using radio_modulated_tx_carrier() function from radio tool code. But when trying to run the code, application is...
Hello,
I am attempting to set up NVS to capture GPS data received from the modem for transmission to NB-IoT after collection has ended.
I have successfully implimented...
Hi everyone,
I m trying to communicate nRF52832 to an android application " nRF52 UART 2.0" on 9.0.
"nRF52 UART 2.0" app source is from git( https://github.com/NordicPlayground...
Hi everyone, I need to send data (coming from many sensors) from a nRF52 to PC via Bluetooth. I have a custom board with nRF52832 and I am using the nRF52 Development Kit...
Hi Team. There is a connection between nrf52840 and esp32-wroom over uart. Uart settings: baud rate - 115200, data - 8bit, HWFC - disable, Parity - excluded, stop bit - 0...
Hi. We have a project we would like to move to an nRF52840 SoC. I have modified the hid generic example to connect with our test software which basically can send and receive...
Hi all!
I want to make my first code in my nrf51 dk (i have an PCA10028). I have experience with M0 and other uC, but i have never play with BT.
Could you guys recommend...
Hi,
I'm trying to improve throughput by increasing the notification buffer number to 6. (SD132, V 5.0.0, SDK14.2)
I tried to follow the sequence charts as well as use...
I'm in trouble because I can't get my expected Logs in WireShark with nRF51822.
[Enviroment] ・I use "User Guide v2.2" and I installed according to this document. ・My PC...
Hello,
I'm using the nRF52832 DK to implement the light switch example in mesh SDK. For this example I'm using nrf mesh app as the provisioner and in this app , to add a...
