Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
I have query on glowing multiple LEDs example 8 LEDS with GPIOs of nrF51422
So went through nRF51822 series based EDK design files and i see they use 4 LEds to which...
Hello,
I have been trying to test the ble_app_beacon example code that comes with SDK11.0 and upon building I got the following error:
Upon trying the ble_app_beacon...
I might be missing something but it doesn't look like the TWI sensor example in SDK 15 even uses the TWI sensor library. It looks like it uses the driver directly.
Also...
Hello
We try to measure package loss if BLE Advertising & BLE Mesh is used in a congested environment. (WLAN accesspoint has MIMO, 18dBm, heavy data transmitting with psping...
Hello Everyone,
I am using nRF52 DK and i have 2 SPI slaves (ADC and EEPROM). ADC works with SPI mode 1 and EEPROM works with SPI mode 0.
I figured that i need to manually...
Hello Nordic, I've been searching the forum and the SDK for code examples that specifically use Bluetooth 5; could you direct me to that code? Many thanks in advance for your...
I am now based on nrf52832 SDK14.2 development, I tried to use the PWM driver and timer to drive the corresponding two IO port an irregular waveform, I originally thought...
I am using the Hackable kit which has nrf52832 to control a servo motor and read accelerometer(AXL335) readings through a iOS app. I am a novice when comes to embedded. I...
Hello, ererybody!
I use nRF52832,have a development board.
I was testing the adc module,using the ANI2 channel,I measured the ANI2 channel voltage to the ground,find it...
Hello everyone,
now i'm working with nRF52840 PDK( Engineering B ) and i migrate my project from SDK 14.1 to SDK 15. My starting point is ble_app_template and i want to...
Hi!
My setup:
* nRF52 DK (let's name it N )
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* two android smartphones (let's name them A1 and...
1. nrf51822-qfaa
2. sdk10.0 & sd8.00
Q:
If the MAX_CONN_INTERVAL is set to greater than 200, NRF_ERROR_INVALID_PARAM will be returned when called sd_ble_gap_ppcp_set...
This post had a discussion on using one button but the first reply suggested a buttonless solution. So now I'm not sure if one button dfu is best if same button is used for...
hi,
i am doing a project where i have to exchange strings between nrf52832 as peripheral and andoird smartphone using nrf connect app, in this project data security is a...
Hello!
It's the first time using Nordic devices so i´m doing some SDK examples and trying to merge them. I'm using SEGGER Embedded Studio. Right now i´m using ble_app_blinky...
