Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello System: Windows 10 Pro 64bit, 1703 I prepare the Toolchain on Win10 for BLE Mesh 2.0.1 SDK. During compilation of "pc-nrfutil-mesh_dfu" i get the error "missing NETAPI32...
Hi Nordic team
I compile the example ble_app_interactive in keil ver.5.24.
And the below error message occur.
I have compiled other examples and it works fine. (except...
Hi
I am designing Circuit with nRF4122 - QFN package 48 pin, as per datasheet there is circuit for Trace/ PCB Antenna
But i am planning to use Chip Antenna and BAL-NRF02D3...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
Hi,
I have completed all steps in the example at the following link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and all...
I am developing hardware for the nRF52840. After testing our firmware, we are going to need somewhere around 6,000-7,000 mAh to run our hardware for the time needed. We were...
Hi, all.
I used sd_ble_gap_addr_get() function to get a MAC address in the different example and the result was different.
I tested this example in SDK v14.2 and v15...
Hi,
The amount of information and reference documents available about Bluetooth qualification is overwhelming. It would be great if someone with this experience sheds some...
Do nRF8001 chip has its own internal linear regulator? or Does it need an external like the module created by Adafruit ( https://cdn-learn.adafruit.com/assets/assets/000/035...
Good evening all,
I'm trying to get my DK52 communicating with a CR95HF (this is a NFC controller with serial and SPI control interfaces), I'm using a breakout board - BM019...
Hi Sir, I use load switch circuit to control nrf8001's power. I found even the vcc of nrf8001 is empty, nrf8001 still works. That's not my expected result, I think nrf8001...
Hi ,
We know that the nRF8001 use the random static device address . I have the questions below :
A. Will the device get one new address after power on ? or is the address...
