I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Using SDK 12.2, I have compiled the secure bootloader successfully, tweaking the sdk_config and Makefile to use RTT for logging and turning on logging, and using the "_debug...
Configuration: Nordic PPK, PCA10040, PC10028 & PCA63511. Current consumption is relatively high on nRF52 vs nRF51; nRF51 is configured with SDK 10.0 and nRF52 with SDK 12...
Hi,
I have got my nRF52 DK. I could flash softdevice using nrfjprog.
But after reading s132 specification, i have following doubts.
How to flash application from the...
Hi all --
I have an application where I have a LDO generating 2.6V from a single lithium-ion cell. It has an EN input that I want to expose to the nRF52 with a little RC...
Hi,
I'm searching for the nRF52 Ref Manual. I've located the Product specification for the nRF52832, but can't seem to find anything for the Reference Manual.
I found...
To maintain compatibility with our current systems we would like to be force characteristics to be at certain handles, rather than having the soft device assign them sequentially...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
Device: PTR5528
Board: custom.
I have just given coin battery directly to VDD. At P0.00, P0.02 i have two leds. On p0.03 and 05 i am having one interrupt and other is...
Hello everyone.
I am currently working on a device with some peripherals.
I have SPI slaves and other sensors that I am monitoring using GPIOTE driver.
I noticed a...
I am attempting to implement buttonless DFU with my application.
Using SDK v12.2.0 on a Rigado BMD-300 module (nRF52832)
Starting one step at a time, using nRFgo Studio...
I am running RTC in nrf51, after coming out of sleep mode RTC is getting reset.I want this RTC to keep running so that we can use it as wake up signal.
I am attempting to enable a second custom service with a vendor specific UUID with three characteristics (in addition to an existing custom service and the battery service...
Hello
I have created one custom profile using "ble_app_uart" project. Now I have an issue that I can't able to remove UART part of the code. If I remove the UART part of...
Dear Team,
when we compile in keil on one of the system we are getting hex file as 30 KB(Programme application which is correct one) & in another system we are getting...
