hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using example->peripheral->uart(KEIL version MDK 5) in SDK11.0 . Because my 52832 board is a new one I made, I changed RX_PIN_NUMBER and TX_PIN_NUMBER to 9 and 8. CTS_PIN...
Hi,I'm using mpu9150 imu sensor with nRF51822 EK kit, i want read that sensor values i.e acceleration, gravity, yaw,pitch,roll values in keil ide ,how i can do that? Can any...
Hi,i'm using the nRF51822 with the IMU 9150 sensor, i'm using the github.com/.../nrf5-mpu-examples git repo for my sensor. while i try to read the values of sensor in Tera...
I am trying to flash TCP-Server example from IOT SDK from Eclipse.
Project builds without errors.
But I am getting this warning message in Eclipse console when I flash to...
s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
I want to use the Central Glucose Service, how do i modify the "ble_central/ble_app_hrs_c" example code?
int main(void...
I wanted to use MQTT example with nrf52 DK board.
and I uploaded MQTT firmware which is located MQTT example folder in iot SDK.
www.youtube.com/watch
I tried to follow...
Hi,
I want to implement handler for undefined instruction fault. According to Cortex M4 documentation (ARM DUI 0553A subchapter 2.3.2 "Exception types") this fault leads...
Hi everyone,
I've been experimenting compiling my project with Clang and have run into some issues with the supervisor calls and their wrapper in nrf_svc.h.
Without...
Hi,
I want to implement simple module:
gpiote event on pin change (around 6.7MHz signal)
Route gpiote event through PPI to increment counter
Toggle GPIO pin...
According to the documentation, the function sd_ble_gatts_exchange_mtu_reply() can return NRF_ERROR_BUSY , which would require the application to somehow defer the call to...
Hi,
I am attempting to run the examples of BLE HRS C and BLE HRS Peripherals from the SDK. Getting to the connected state works (discovery and notifications as well) just...
I noticed that the ram setting in this example is from 0x20003440, this means only less than 1KB is for application. But the example in sdk 12.1 the ram is from 20002078....
We want to use IoT SDK where two or more nRF52 chips would talk to each other via 6lowpan, in that case is the ble enabled router necessary for such communication?
