I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
HI,
I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
EDIT
I think there is somewhere in KEIL or nrf libraries a bad pointer type alignement .
The correct pointer is given as uint_32_t ( NRF_SAADC->RESULT.PTR = (uint32_t...
I notice that each dev board has a version of nrf_drv_config.h in the config folder. For my custom target, I want to create my own version of this file where I will modify...
I use nRF52832 as a master to communicate with ads1292. then I want to config the ads1292, so i should send the register address and configuration data.But I don't know how...
Hi,
I tried to compile my own program with eclipse and GCC with c/c++.
I followed this tutorial : TUTORIAL
I have some problems :
First : i have problem with...
Hello,
I developed a code (softdevice S110 and SDK 10) on a prototype based on a NRF51822G2 chip. I tried to reproduce the prototype with NRF51822H0 chip.
I flashed...
Hi,
I use ESB protocol, and all is working fine :)
Now I want to retreive the address of the sender because I can have multiple sender in my network.
I can add this...
With there being +/- 4dBm variability in output power from nRF52 to nRF52, each device needs to be calibrated in order to comply with FCC rules. One of the rules is there...
Hi
I'm porting a nrf51822 project with S110 to a nrf52 board. In this case, I'm a bit confused about which softdevice to use. S132 it is the equivalent to the S110? Or...
Hello everyone,
I am using the nRF52832 rev 1, i am not using the softcore. When the cache is enabled as below, the performance actually seems to get worse.
F_NVMC-...
using Bluetooth Developer Studio, and
nRF52 SDK v11.0.0 - Experimental: Bluetooth Developer Studio Example
I have created a profile using BDS and generated the files with...
In order to teach a class of students using nRF developer boards I'd like to use the nRF Blinky application running on Android, iOS, or whatever mobile platform. The problem...
