Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I want to use the MultiActivity Example with the nRF52 with GCC and Eclipse.
In the documentation I ve read that S130 and S132 are supported, but in the directory of the...
When I using the UART port, if I float the port after init the UART it will restart the code, is it need a external pull-up resistor? How about the value?
A quick one, where do I find a list of the err_codes? I have had a look in the documentation and I was expecting to find a table of them, but I couldn't locate one.
Thanks...
Hello!
I am trying to send a notification to a peer device when a certain event occurs. To do so, I'm using the same procedure as with every other characteristic with enabled...
I used the example of the ble_central\ble_app_uart_c and ble_peripheral\ble_app_uart.
It seems no problem for operation when I check only this example.
But I modified this...
Hello Everyone ,
I ahve deveoped the custom board using NRF51SOC and i have flashed the custom board by usign P20 Connector referred below figure now i would like to debug...
If I let the SoftDevice write to my variables directly by having the characteristics point to my app's variables through BLE_GATTS_VLOC_USER - when are these variables actually...
HI,i have some problems about RSSI (51882)
BELOW IS MY CODE. who can tell me why I can not get RSSI from variable t
int main(void)
{
uint8_t *p;
uint8_t t = 0;
...
Hi,
In S130, both central and peripheral modes are enabled. How do you enable just the peripheral mode and not the central mode for S130 so that less RAM space is used...
I am just working through the tutorial on radio notifications and imported "ble_radio_notifications.c" to my application folder and included the header in included directories...
I use NRF51822 Bluetooth 4.0 e-val kit.
souce code is peripheral example.
so, android smart phone and NRF51822 is connection.
result, Pairing success. occur On_ble_evt...
Is it possible to detect a bluetooth (BLE) enabled phone when it enters the room?
I like to use the nrf51822 (BLE-Peripheral or BLE-Central) to detect any phone when it...
Is it possible to have S110 but not more than ~30-40K size? I need to establish communication in order to upgrade firmware over BLE (UART Emulation), but without using such...
Hello,
Situation:
I am trying to write a characteristic to an iOS device acting as a peripheral from a nRF51822 board.
The board has 2 leds (green and red) and a button...
What is the file pstorage_platform.h? Is it an SDK file? Where does it come from? Is it auto-generated somewhere or should it be just copied from an example?
