I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I want to control LED of the Server 2. (Turn on / off) by using Client.
How to add the relay node in light switch example (this is one of the basic example...
I am trying to update a device using a Macbook pro with Sonoma 14.4 and am receiving an error message that states that nordic "Did not receive checksum response from DFU target...
hello, I'm using nrf52DK & connect sdk v2.6.1. I'm in the process of migrating from nrf5 SDK to connect SDK.
My previous code to read Mac address to form unique BLE names...
I am getting a warning in my nrf5340 overlay file because I ran out of pins and need to reassign P0.30 to my BMI270 interrupt 1. Here is the message in the overlay file: ...
I am using visual code studio, zephyr RTOS, v2.5.2 on NRF52840
I am trying to find a QSPI example
I noticed someone mentioned the sample :spi_flash is using QSPI ? But...
Hi,
I'm migrating my application from SDK v2.4.1 to v2.6.1. In my application I'm using Zypher BLE Controller with HCI_rpmsg child image. I renamed the hci_rpmsg to hci_ipc...
Hi.
Can you please tell me how to erase the chip in VS Code without writing new firmware?
In Segger Embedded Studio there was such an option (Target -> Erase All), but...
Hello,
I am currently trying to figure out why my application stops working after some time (can be hours to days).
Im am using a nRF9160-DK, with the nRF91 programmed...
Hello,
I am working on a BLE application based on the nRF52840 and NCS 2.5.0.
I'd like to reduce or disable the packet retransmissions. I've looked through the NCS documentation...
I have a firmware project currently developed in a Nordic nRF52840 chip. I am trying to create a new board ( we are updating the PCB ) to implement the same firmware on a...
I have an existing project with a custom board. It builds from VSCode and command line with ncs 2.6.0. With 2.7.0 it builds from vscode, but not from the command line (see...
Hi all, For this project firmware overview: A few months ago, we shipped 10k products and never had such problems. In the latest order, 38 out of 1k products were abnormal...
When using two 52833 boards for distance measurement, when testing at 60cm, the distance value obtained sometimes wobbles between 0.6-1.2m, but sometimes stabilised around...
Can I use gazell device and ble host on one nRF52840 chip at the same time? If so, can you tell me how to develop it? Or give me an example for reference.
